Settings

Add device

      Available from both (Houseper and Houseper mobile) applications. More...

Add camera

     Available from Houseper application only. More...

E-mail Settings

     Available from Houseper application only. More...(see E-mail notifications)

Configure alarm notifications

     Available from Houseper application only.

    In that section are all default settings for sending notifications. Each device inherits these settings when it is added. Subsequently they can be changed for a specific device.

1. alarm indicator - optional only if the event is an alarm type
   
2. event name with optional explanation - The name may be quite specific, such as Tamper, Battery, etc. or collectively as it is shown of the picture. Alarm 1 and Alarm 2 are collective names depending of the particular device and can look like Fire indication, Water overflow indication, Intrusion indication, Movement indication, Presence indication, Panic, Emergency, and so on.
   
3. defines sending notifications to all configured smart phones/tablets
4. defines sending emails to all configured email addresses
5. defines the activation of a siren if it has been added to the system and if it is active.
6. defines the activation of a siren if it has been added to the system and if it is not active - There are cases that can be defined as very urgent and important for which we would like the siren to turn on.

    At the bottom of the Configure alarm notifications section you'll find Restore options. These options apply for automatically clearing alarms when receiving an alive report. When a device has an active alarm, such as an open door and this alarm disappears when the door is closed, some devices depending of their type send a report to cancel the existing alarm. There are two options

1. Never restore alarms, before it is manually cleared - alarms will not be automatically deleted when you receive an alive report. Manually deleting is the only way to remove them.
2. Restore alarms depending device default options - when this option is selected, the alarms for which the recovery report is received will be cleared automatically.

    To receive notifications on your smartphone/tablet, you need to be sure that:

1. Your phone has been successfully authorized at the controller and "send notifications" is selected in the list of authorized devices at the Houseper application, Settings tab, Remote Control.
   
2. Your smartphone/tablet has been successfully registered to receive notifications - the "registered" status is displayed in the Settings tab, Notifications section of the Houseper mobile application. If you have problems, you can do a  Test and/or  Renew registration.
3. You have not reached the limit of unread notifications for your mobile device.
   

Electricity pricing

     Available from Houseper application only. More...

Remote control

     For more information, see Remote control

Language

     To change the application language, select Language from the Settings tab.

     It contains information about the Zigbee network. Note that sleeping devices can leave the Zigbee network for a long time (are missing from this list). When "wake up" they will appear again.

1. controller identifier
   
2. signal strength indicator for a router device
3. signal strength indicator for an end device that is not a router
4. a list of the names of all logical devices that are contained in the physical device
5. additional information - network address, MAC address and signal strength
6. remove device button
7. hide/show the children connected to the device

Data cleaning

     Ability to configure automatic clearing of old data.

Check for update

     Checks for a new version of the Houseper application. If a new version is available, information about the changes made is provided  and the update can be installed.

System info

   It contains basic system information such as:

1. Houseper Id - A unique controller identifier needed to activate cloud services
2. Android Id - unique service number
3. Application version
   
4. Remote URI
   

       
   

Payments

     Contains information about:

• activated additional services - service name, validity date, current status
• opportunity to pay for additional services

    It also contains a history of payments.

    The maximum eligible prepayment period is one year.

Zigbee restart

     Restarts the Zigbee controller module

Factory reset

     Removes all devices, clears the collected data and re-initializes the home automation module. When using this feature you will be offered to save some data.

     It is important to keep in mind that if the operating system is back to factory settings, the Houseper application will also be reset and all data will be cleared, but the Zigbee controller module will remain old data that should be removed with the Factory reset button.